How To Create Local Area Connection In Windows 7

1. 1

   Make up one's mind the number of computers you want to connect. The number of computers you're connecting will determine the blazon of network hardware you'll demand.

   • If you are connecting four or less computers, yous'll just need a unmarried router, or one switch if y'all don't need internet.
   • If you're connecting more than than iv computers, you lot'll want a router and a switch, or just a switch if you lot don't demand cyberspace.

2. two

   Decide your network layout. If your installing a permanent LAN solution, you'll want to keep cable length in mind. CAT5 Ethernet cables should non run longer than 250 feet. If you demand to cover larger distances, you'll need switches at regular intervals, or y'all'll demand to utilize CAT6 cables.

   • You'll need one Ethernet cablevision for each computer you desire to connect to the LAN, as well as an Ethernet cablevision to connect the router to the switch (if applicable).

   Advertizing

3. 3

   Obtain the network hardware. To create a LAN, y'all'll need a router and/or a network. These pieces of hardware are the "hub" of your LAN, and all of your computers will exist connected to them.

   • The easiest style to create a LAN where every computer has access to the cyberspace is to use a router, and then add a network switch if the router doesn't accept enough ports.^[ane] A router will automatically assign an IP address to every computer that is connected to it.
   • Switches are similar to routers but practice not automatically assign IP addresses. Switches typically have many more Ethernet ports than a router has.

4. iv

   Connect your modem to the WAN port on the router. This port may be labeled "INTERNET" instead. This will provide internet access to every computer that is continued to your LAN.

   • You can skip this if you're setting up a LAN without internet access.
   • You don't demand a router at all to create a LAN, but it makes things easier. If you just utilize a network switch, yous'll need to manually assign IP addresses to each calculator after connecting them.

5. 5

   Connect the switch to a LAN port on the router. If you're using a network switch to connect more than computers, connect information technology to one of the LAN ports on the router. You lot can use any open port on the switch to brand the connection. When continued, the router will provide IP addresses for every computer that is connected to either device.

Advertisement

1. ane

   Find the Ethernet port on your PC. You tin can usually observe this on the back of your desktop tower, or along the side or dorsum of a laptop.

   • Slim laptops may not accept an Ethernet port, in which case y'all'll need to either utilise a USB Ethernet adapter or connect wirelessly if your router allows information technology.

2. two

   Plug 1 end of an Ethernet cablevision into your computer. Make sure y'all're using an Ethernet cablevision (RJ45), not a telephone cablevision (RJ11).

3. iii

   Plug the other end of the cable into an open LAN port. This can be any open LAN port on either the router or the switch, depending on your LAN setup.

4. 4

   Test out your network (router only). If you're using a router, your work is consummate. Once all of the computers are connected to a LAN port, they will be assigned IPs automatically and will appear on the network. If you set your LAN for gaming, you should be able to starting time your LAN game and accept each computer connect.^[ii]

   • If you're using a switch and no router, y'all'll yet need to assign IP addresses to each calculator.

5. 5

Advertisement

1. one

   Right-click on your network connection. You lot'll see this in your Arrangement Tray. If you are connecting your computers through a switch with no router, yous'll demand to assign each computer on the network its ain individual IP address. This procedure is handled automatically if you're using a router.

   • Call back of an IP address as a mailing accost. Each computer on the network needs a unique IP address then that information sent across the network reaches the correct destination.

2. ii

   Click Open up Network and Sharing Eye .

3. 3

   Click the Ethernet link at the top of the window. You'll see this next to "Connections."

4. 4

   Click Backdrop .

5. 5

   Click Internet Protocol Version 4 (TCP/IPv4) . Make sure you don't uncheck it, merely highlight it.

6. 6

   Click Properties .

7. seven

   Click the Use the following IP address radio push button.

8. 8

   Blazon 192.168.1.fifty into the IP accost field.

9. 9

   Type 255.255.0.0 into the Subnet mask field.

10. ten

    Type 192.168.0.0 into the Default gateway field.

11. 11

    Click OK . This will save the settings for that computer. This reckoner is now configured on your network with a unique IP accost.

12. 12

    Open the Internet Protocol Version four properties on the next estimator. Follow the steps above on the second estimator to open the Cyberspace Protocol Version 4 (TCP/IPv4) Properties window.

13. 13

    Click the Apply the following IP address radio button.

14. 14

    Type 192.168.1.51 into the IP address field. Notice that the final group of numbers has incremented past 1.

15. 15

    Enter the same values for Subnet mask and Default gateway . These values should exist the same as they were on the first computer (255.255.0.0 and 192.168.0.0 respectively).

16. 16

    Give each additional figurer a unique IP. Repeat these steps for each additional calculator, incrementing the IP accost past 1 each time (up to 255). The "Subnet mask" and "Default gateway" fields should be the same on each computer.

Advertisement

Add together New Question

• Question

  What is subnet mask in IP addresses?

  

  Mitch Harris is a Consumer Applied science Good based in the San Francisco Bay Area. Mitch runs his own Information technology Consulting visitor called Mitch the Geek, helping individuals and businesses with home office engineering, data security, remote back up, and cybersecurity compliance. Mitch earned a BS in Psychology, English language, and Physics and graduated Cum Laude from Northern Arizona University.

  

  Consumer Technology Expert

  Proficient Reply

  A subnet mask separates where the inside of the network is and where the outside earth is.

• Question

  What should I do if whatever website is non opening?

  

  Mitch Harris is a Consumer Engineering science Expert based in the San Francisco Bay Expanse. Mitch runs his own Information technology Consulting company called Mitch the Geek, helping individuals and businesses with dwelling office technology, data security, remote support, and cybersecurity compliance. Mitch earned a BS in Psychology, English, and Physics and graduated Cum Laude from Northern Arizona University.

  

  Consumer Technology Good

  Proficient Answer

  Make sure that you've entered a DNS server—if you lot oasis't, yous'll receive an mistake related to DNS and you won't be able to access whatever webpages. You can enter Google's free server with "viii eight viii 8" or "viii 8 4 four". If you use Comcast, enter "7 v 7 5 7 5 7 5" or "7 five seven 5 7 half dozen 7 vi".

• Question

  How do I connect a printer to a LAN?

  

  Properly configure the IP of the printer, and connect it to your switch or router -- preferably a router (it volition assign an IP that is compatible to your network). Make sure the port yous are using is open up.

• Question

  How can I recover my Wifi password?

  

  Go to the help desk-bound of your provider and enter your account details and they volition help y'all recover it.

• Question

  What is the IP address?

  

  A unique cord of numbers separated past full stops that identifies each reckoner using the Internet Protocol to communicate over a network.

• Question

  My computer is connected to the internet by WiFi, but cannot pull up a site. What should I do?

  

  Try rebooting your WiFi router and your estimator. If that doesn't work, try contacting your ISP.

• Question

  We get an error message that says "unidentified network." The cable, switch, and router are working. What should I do?

  

  Effort resetting the modem/router.

• Question

  I have an intermittent connectedness with my television. How practice I stabilize it?

  

  Try using another cable or if y'all are using WiFi, try placing your router in a amend location.

• Question

  How do I assign an IP accost to my desktop?

  

  The best way would exist to set a static IP address on your router. Check the manufacturer'due south website for directions specific to your device. An alternative is to set a static IP through your OS. Notwithstanding, this tin can create network collisions if another PC on your network has the same IP accost.

• Question

  How do I configure my PC to connect information technology to the network?

  

  Either wireless or wired, make certain you have connected it to the network by your Ethernet cable or by wifi.. 1st. A router will automatically do configurations for yous as long as it is on the network, if not, use a switch, and configure manually. settings>network and internet>ethernet>modify adapter settings>choose the right network y'all are connected to>rightclick>backdrop>ipv4 settings>static ip addressing. make certain the default gateway are the aforementioned on all pcs, and the subnet mask, and then relieve and okay.

Ask a Question

200 characters left

Include your e-mail address to get a bulletin when this question is answered.

Submit

Advertisement

About This Article

Article Summary X

1. Plug an Ethernet cable into your PC.
ii. Connect the other end of the cable to the LAN port.
three. Open your network settings.
4. Enable file and printer sharing.
five. Assign an IP address if you're not using a router.

Did this summary assist you?

Thanks to all authors for creating a page that has been read one,062,937 times.

Is this commodity up to date?

Source: https://www.wikihow.com/Configure-Your-PC-to-a-Local-Area-Network

Posted by: burnsallasted88.blogspot.com

Share this post